Next product

Previous product

Repcoat FF

Repcoat
S

SOLVENT BASED PROTECTIVE COATING

Advantages:

Excellent protective barrier against chloride ions, carbon dioxide and water
Durable - highly resistant to UV and weathering
Moisture vapor permeable, allows concrete to breath
Available in a wide range of decorative colours
Single component
Colour stable, with excellent hiding power

Description:

Repcoat S is ready for use, single component, aliphatic acrylate coating for external and internal use over variety of concrete and masonry substrates. The system also includes an under coat of a silane-siloxane base which when used with Repcoat S will provide maximum protection against chloride ingress and carbon dioxide diffusion.

Usage

Repcoat S is an excellent protective and decorative fair face coating which can be used for many applications including:

retaining walls,
bridge abutments,
external concrete of storage tanks,
multistory buildings and villas,
pre-cast elements and concrete cladding,
commercial and Industrial complexes.

Materials Supplied

Repcoat S is available in packs: 18 l.

Coverage

Depending on substrate

0.16 l/ 1 m²/ 1 coat

Storage/ Shelf Life

Repcoat S has a shelf life of 12 months if stored in proper conditions, at temperatures range between + 10°C and + 25 °C in its original unopened packing.

Technical Information

Volume solids	40 – 45 %
Over coating time for Repcoat S Primer	5 h @ 25°C
Carbon dioxide diffusion resistance: Taywood method	> 250 m equivalent thickness of air
Carbon dioxide diffusion resistance: Taywood method	> 500 m equivalent thickness of concrete
Touch dry time	25 min
Application temperature	+5°C to 35°C
Water vapor diffusion resistance	S_D 1.90 m @ 150 microns dft
Freeze/thaw salt scaling (50 cycles)	Unaffected
Good quality concrete (control) ASTM C672	Severe scaling
Fire testing – Spread of flame: BS 476, Part 7	Class I
Fire testing – Propagation: Index I Sub index I1 Building Regulations rating BS 476, Part 6	1.5 1.3 Class 0

Application Information

SUBSTRATE PREPARATION

Surface preparation is very important to get a good quality finish and best performance. Any surface to be coated must be clean, sound and free from oil, grease, curing compound, or any contamination. Any contaminants should be removed by light grit blasting.

Surfaces containing slight surface imperfection or blow-holes should be filled with a skim coat of cementitous repair mortar such as Cemfair PF. Deep holes and defected areas should be repaired with cementitous products from DCP-Repair range.

APPLICATION

The prime coat should spray or brush applied at the rate of 0.2 ltr per square meter.
It is recommended to apply two coats of Repcoat S at the stated rate of application.
The first coat should be applied evenly by roller, brush or airless spray machine at a rate of 0.16 litre per square meter and allowed to dry.
The second coat should be applied perpendicular to the first coat at the rate of 0.16 litre per square meter. Repcoat S needs to be thinned up to 5% by weight when using airless spray machine.

HEALTH & SAFETY

As with all paints, care should be taken during use and storage to avoid contact with skin, eyes and mouth. Wear suitable protective clothing, gloves and eye/face protection.

Should accidental skin contact occur, remove immediately with plenty of clean water. If swallowed, seek medical attention immediately - do not induce vomiting.

For further information refer to the Material Safety Data Sheet.

FIRE

Repcoat S is flammable.

Ensure adequate ventilation. Do not use near a naked flame and do not smoke during use

Download file

Technical Data Sheet

How to

Connect with Don Construction Products

Don Construction Products Bulgaria EAD

Sales office

Monday - Friday: 9:00 - 17:30

Sofia 1582, Bulgaria

152 Prof. Tsvetan Lazarov blvd.

Techno Park Sofia

Tel.: +359 2 870 2782; +359 2 870 2761

info.bulgaria@dcp-int.com

Technical support

+359 2 870 27 82

Contact form

Get Contact Form

Name *
Email *
Phone
Address
Reason
Request
Security Code *

RepcoatS